u♦ s» JJAft DEPT„ TECHNICAL MANUAL 8-628 
INSTRUMEWT STERILIZER ITEM 7917005  
WAR DEPARTMENT TECHNICAL MANUAL 
INSTRUMENT 
STERILIZER 
ITEM 7917005 
WAR DEPARTMENT 
NOVEMBER WAR DEPARTMENT TECHNICAL MANUAL 
TM 8-628 
INSTRUMENT 
STERILIZER 
ITEM 7917005 
WAR DEPARTMENT 
NOVEMBER 1944 
United States Government Printing Office, Washington ; 1944 
For sale by the Superintendent of Documents, Washington, D. C. WAR DEPARTMENT, 
Washington 25, D. C., 4 November 1944. 
TM 8-628, Instrument Sterilizer, Item 7917005, is published for the informa- 
tion and guidance of all concerned. 
[A.G. 300.7 (28 Sep 44).] 
By order of the Secretary of War; 
G. C. MARSHALL, 
Chief of Staff. 
Official: 
J. A. ULIO, 
Major General, 
The Adjutant General. 
Distribution: 
Armies (2); Corps (2); Depts (10); SvC (5); ID 8 (4); IB 8 (1); 
IR 8 (3) (2) (1); IC 8 (2); Base C (5); Numbered Air Forces (5); 
Med Deps, Continental (25) except St Louis Med Dep (50), T of Opn 
(10); PE (2). 
ID 8: T/O & E 8-550. 
IB 8: T/O & E 8-611; 8-610. 
IR 8 (3): T/O & E 8-581; 8-580, Evac Hosps. 
IR 8 (2): T/O & E 8-560; 8-510; 8-590, 
IR 8 (1): T/O & E 8-580, Conval Hosps. 
IC 8: T/O & E 8-187; 8-572S; 8-667. 
For explanation of symbols, see FM 21-6. 
II CONTENTS 
CHAPTER 1. INTRODUCTION Paragraph Page 
Scope 1 1 
Description 2 1 
Data 3 1 
CHAPTER 2. OPERATING INSTRUCTIONS 
General 4 5 
Service upon receipt of equipment 5 5 
Controls 6 5 
Operation 7 6 
CHAPTER 3. MAINTENANCE 
General 8 8 
Operator’s preventive maintenance 9 8 
Trouble shooting 10 8 
Maintenance operations 11 11 
APPENDIX I. SHIPMENT AND STORAGE 15 
II. LIST OF ALL SERVICE PARTS 15 
III. LIST OF ALL SERVICE PARTS 16 
IV. WAR MODEL 214C 17 
V. PRE-WAR MODEL 214C 18 
VI. MODEL NO. WPB-13 19 
VII. MODEL NO. C—413 20 
III CHAPTER 1 
INTRODUCTION 
1. SCOPE. These instructions are published for the information and guidance 
of all personnel charged with the operation and maintenance of Sterilizer, 
small, 110-volt, a-c-d-c, Medical Department Item No. 7917005, in the field. 
They contain information on the operation and maintenance of the equip- 
ment with illustrations showing the various parts referred to in the instruc- 
tions. This Technical Manual is arranged in four parts: Chapter 1—Introduc- 
tion; Chapter 2—Operating Instructions; Chapter 3—Maintenance and the 
Appendix which lists all service parts by manufacturers. Inasmuch as prac- 
tically all small officer sterilizers of the nonpressure type are similar in design, 
construction and operation, these instructions are written to apply generally 
to all such sterilizers. 
2. DESCRIPTION. The Sterilizer, instrument, small, 110-volt, a-c-d-c is a 
small, compact unit designed for sterilization of small surgical instruments. 
Boiling water is the sterilizing medium. The units employ electrically oper- 
ated heater elements to heat water contained in a boiler. Caution must be 
used when ordering replacement parts for these units since they vary in 
serial number, as well as model number in some cases. The serial numbers 
and model numbers are usually found on the nameplates attached to the unit. 
Be certain when ordering spare parts that the part ordered is specifically for 
the model or serial number as shown in the list of all service parts in the 
Appendix, If the part is not listed as a spare part, it must be requisitioned 
for special purchase. 
3. DATA. a. Performance. The sterilizer is designed to operate on 110- 
120-volts, 60-cycle a-c, or d-c. 
b. Manufacturers. American Sterilizer Co., New York, N. Y. 
The Prometheus Electric Corporation, New York, N. Y 
The Pelton & Crane Company, Detroit, Mich. 
Wilmot Castle Company, Rochester, N. Y. 
1 figure 1. Sterilizer, instrument, small, 110-volt, a-c—d-c, item No. 7917005, manufactured by the Prometheus Electric 
Corporation. 
2 Figure 2. Sterilizer, instrument, small, 110-volt, a-c-d-c, item No. 7917005, manufactured by the Felton & 
Crane Company. 
a FigUre 3- Sterilizer’ instrument, small, 110-volt, a-c-d-c, item No. 7917005, model No. WPB-13, manufactured by Wilmot Castle 
Company. 
4 CHAPTER 2 
OPERATING INSTRUCTIONS 
4. GENERAL. The hours of operation of the sterilizer are dependent upon 
the requirements of the Medical Officer. It is general practice to operate the 
sterilizer the entire time the Medical Officer is on duty and using instruments, 
since the various instruments used should be sterilized immediately after use. 
However, since the operation of the sterilizer is simple, it may be put into 
use at any time. 
5. SERVICE UPON RECEIPT OF EQUIPMENT, a. Unpacking. To unpack 
the sterilizer, open the shipping box carefully. Remove packing materials, 
and lift the apparatus from the shipping box. 
b. Assembling. The item is shipped completely assembled and ready for 
use after inserting the line cord plug into a power receptacle. In some cases 
the lever handle must be screwed onto the lifting lever. 
6 CONTROLS, a. Switch. Many models and makes have a 3-pole switch 
which enables the operator to select the required or desired amount of heat. 
The switch settings are “Off,” “Low,” “Medium” and “High.” When the 
switch is turned to “Off,” the unit receives no current. The “High,” “Medium” 
and “Low” settings are self-explanatory as pertaining to the amount of heat 
obtained from the heating elements. Some models use a mercury switch rather 
than 3-pole switch. The same principle as used in the 3-pole switch is used, 
however. One setting uses two mercury switches and two heaters, a second 
setting one switch and one heater, and a third setting is the “Off” position, 
b. Low water cut-off. The low water cut-off is a protective device. Some 
sterilizers use a mechanical low water cut-off, some use a bimetallic thermostat. 
The general purpose is the same. 
(1) Mechanical low water cut-off. Generally incorporates a nonexpanding 
rod anchored to the boiler. When water in the sterilizer has reached a very 
low depth or boiled away, the boiler is heated to a higher temperature than 
when it contains water. The boiler expands causing the nonexpanding rod 
to trip a switch which breaks the electric circuit. This stops the heating of 
the boiler and indicates the low water condition to the operator who fills the 
boiler with water, manually resets the low water cut-off, and the sterilizer is 
again ready for use. By breaking the electric circuit the current is cut off, the 
boiler is not over-heated, and damage to the unit is prevented. 
(2) Thermostatic low water cut-off. Operates in a similar manner. Exces- 
sive heat from the boiler causes the diaphragm disk on the bimetallic thermo- 
stat to snap open and thus break the electrical circuit. The unit then cools off. 
5 However, upon cooling off, the bimetallic disk snaps shut, completes the elec- 
trical circuit, and heat is again applied to the boiler. Therefore, it is necessary 
to fill the boiler with water or turn the machine off until the boiler is filled, 
otherwise the current will alternately be on and off until this is done. Should 
the operator fail to note that the thermostat is opening and closing the circuit, 
no damage will be done to the sterilizer; however, the unit should be turned 
off or the boiler filled if continued in use. 
7. OPERATION. The sterilizer boiler should be clean. If necessary, scrub 
boiler interior, needle and instrument trays with a stiff brush and soap and 
rinse well before using. Fill the boiler with fresh water. Insert plug into 
power receptacle. Turn switch to “High.” Bring water to a boil. Place 
instruments and needles in the trays and carefully lower trays into water. Be 
sure entire load to be sterilized is completely submerged; never allow any part 
to be exposed above water. During sterilizing period it is not necessary that 
the water boil vigorously. However, the water must be kept at a rolling boil. 
When water reaches the vigorous boiling point with the switch on “High,” 
turn the switch to “Low” or “Medium,” whichever setting will keep water at 
a boil. At end of prescribed boiling period, remove instruments immediately. 
(Never add fresh water to sterilizer during sterilizing period as this will reduce 
the water to below sterilizing temperature.) Turn switch to “Off.” If steriliz- 
ing is to be repeated, add fresh water, if needed, bring to boil and repeat above 
operation. 
6 Figure 4. Sterilizer, instrument, small 110-volt, a-c-d-c, item No. 7917005. manufactured by the Prometheus Electric Corporation, with false bottom removes 
5. 7R00604 Jacket, Outer, Steel Enameled. 
6. SR00694 Switch, 3 Heat, Arrow 9622 or Bryant 6269. 
7. 7R00606 Boiler, Cast Iron. 
1. 7R00616 Thermostat, Positrol. 
2. 7R00624 Spacer, Iron. 
3. 7R00620 Element, Heating, Complete. 
4. 7R00622 Grill. 
7 CHAPTER 3 
MAINTENANCE 
8, GENERAL. Preventive maintenance includes the systematic attention to 
water level and general cleanliness, the inspection of electrical leads and controls 
to determine that they are in good condition and the prevention of abuse to the 
equipment. 
9. OPERATOR'S PREVENTIVE MAINTENANCE, a. Before Operating. 
(1) Be certain that boiler is clean, clean if necessary. 
(2) Determine that water is at desired level. 
(3) Examine drain cocks and boiler for leaks. 
(4) Inspect electrical wiring for good condition and avoid excessive twist- 
ing of the cord. Do not allow sterilizer legs or any other heavy sharp cornered 
objects to rest on the cord. 
(5) Make certain the plug prongs fit tightly into the power receptacle. 
b. During Operation. (1) Inspect for changes in water level. 
(2) Watch for abnormal variations in temperature. 
c. After Operation. (1) Keep the unit clean and free of dust. 
(2) Make sure all switches are “Off.” 
(3) Inspect boiler for accumulation of scale or lime deposits. Clean if 
necessary. 
(4) Rinse and wipe boiler dry at end of each day. 
10. TRQUBLE SHOOTING, a. If unit fails to heat when switch is turned 
on. 
Possible causes 
Cord plug not plugged in. 
Low water cut-off not reset. 
Loose wiring connections. 
Broken cord. 
Burned out element. 
Possible remedies 
Be certain cord plug is inserted properly 
into power source receptacle. 
Manually reset the low water cut-off. 
Connect wires to proper terminals or plug. 
Repair cord. Refer to higher echelon for 
replacement or repair. 
Replace element. Refer to higher echelon 
for repair or replacement. 
b. If low water cut-off "kicks out" during use. 
Possible cause 
Water is low or no water. 
Possible remedy 
Add water. 
8 FigUre 5' SteriUzer. instrument, small 110-volt, a-c-d-c, item No. 7917005. manufactured by the Pelton and Crane Companv. with false bottom removed. 
8. 7R00048 Spring, Rod, Low Water Cut-Off. 
9. 7R00004 Trip, Cut-Off. 
10. 7R00012 Blade, Contact, Low Water Cut-Off. 
11. 7R00014 Drum, Contact, Low Water Cut-Off. 
12. 7R00016 Block, Contact, Porcelain, Low Water Cut-Off. 
13. 7R00050 Wire, Heater, Asbestos Covered. 
1. 7R00052 Knob, Valve Plug. 
2. 7R00056 Body, Drain-Off Valve. 
3. SR00694 Switch, 3 Heat, Arrow 9622 or Bryant 6269. 
4. 7R00046 Element, Heating, for Model 214C, Complete. 
5. 7R00002 Rod, Porcelain. 
6. / R00008 Knob, Plunger, Low Water Cut-Off. 
7. 7R00010 Plunger, Low Water Cut-Off. 
9 Figure 6. Sterilizer, instrument, small, 110-volt, a-c-d-c, item No. 7917005, model No. WPB-13, manufactured by Wiltnot Castle Company, with false bottom 
removed. 
5. 7R00412 Jacket. 
6. 7R00422 Brace, Angle. 
7. SR00694 Switch, 3 Heat, Arrow 9622 or Bryant 6269. 
8. 7R00420 Thermostat. 
1. 7R00410 Boiler Cast. 
2. 7R00418 Spacer, Brass. 
3. 7R00430 Element, Heating, for Model WPB-13, Complete. 
4. 7R00432 Grill. 
10 11. MAINTENANCE OPERATIONS, a. Low water cut-off. If the unit 
has a low water cut-off which requires manual resetting, make certain the 
cut-off has been reset before operating. If the low water cut-off, “kicks out” 
during use, it is an indication that the water is low and more should be added. 
If the unit has a thermostat this will not be experienced, but the unit will go 
on and off alternately and if this occurs water must be added. 
b. Wiring. Unscrew the eight screws (or four legs) from the false bottom 
and remove it. Examine the wiring to see that the wires are all connected 
to the post studs. If it appears that a wire is loose, connect it to the proper 
terminal using the proper wiring diagram as a guide. If trained repair person- 
nel are available, call in a trained man to make the repair. Often wires of the 
cord come loose from the plug. A visual inspection will show this. Unscrew 
screw from plug. Replace wire by wrapping it around screw in the direction 
in which the screw will be turned. Leave no loose ends. Replace screw. 
Insert plug into receptacle and observe if trouble has been corrected. 
c. Broken cord and burned out element. When it is apparent that either 
or both of these conditions exist, the repair should be accomplished by a 
higher echelon. 
d. Removal of scale or lime deposits. From time to time as warranted 
by a visual inspection, scrub the inside of the boiler and the trays with a stiff 
brush and soap. 
e. Should scale form in the boiler through inattention, prepare a 10 percent 
hydrochloric acid solution in sufficient quantity to fill the boiler to the top of 
the scale. Boil the solution for 15 minutes. This will loosen scale so it can 
be scrubbed out with a stiff brush. Then drain solution, rinse boiler thoroughly 
and wipe dry. Be sure to wipe off under side of cover thoroughly, and do not 
spill solution on exterior of sterilizer or on cabinet top. If trays are also coated 
with scale, leave in sterilizer while boiling solution and rinse and dry same as 
boiler. 
a THERMOSTAT 
Figure 7. Wiring diagram for sterilizer, instrument, small, 110-volt, manufactured by the Prometheus Electric Corporation. 
ELEMENT 
ELEMENT 
LINE 110 VOLTS 
MEDIUM 
LOW 
SWITCH 
HIGH 
OFF 
12 PLUG 
Figure 8. Wiring diagram for sterilizer, instrument, small 110-volt, manufactured by Felton and Crane Company. 
CONTACT BLOCK 
ELEMENT 
ELEMENT 
3 HEAT SWITCH 
13 LINE 
[ 110 
Volts 
Figure 9. Wiring diagram for sterilizer, instrument, small 110-volt, manufactured by Wilmot Castle Company. 
LOW WATER CUT-OFF 
THERMOSTAT 
CURRENT CONTROL 
HEATERS 
14 APPENDIX I 
SHIPMENT AND STORAGE 
1. DISASSEMBLING. Remove line cord from power source. Drain water. 
Dry the unit and it is ready to be packed. 
2. PACKING. Use packing materials such as paper or excelsior and make 
certain the unit is packed firmly in the case to prevent shifting in transit. 
APPENDIX II 
LIST OF ALL SERVICE PARTS 
7917005 Sterilizer, Instrument, Small, 110-volt, 
a-c-d-c: 13 by 5 by 3% inches. 
Prometheus Electric Corp. 
Fig. 
No. 
Medical 
Dept. No. 
Nomenclature 
Unit 
Quan- 
tity 
Common Farts 
SR00042 
Washer, screw size 6, 1 lb. pkg., 1,300 washers 
Pkg- 
SR00043 
Nut, 6 x 32, hex, 144 to pkg. ... * 
pkg- 
SR00104 
Screw, 6-32 x 3/16 inch, R. H. M., 144 to pkg 
Pkg- 
SR00109 
Screw, 6-32 x 1 inch, R. H. M., 144 to pkg 
Pkg- 
SR00142 
Screw, 10-32 x 3/4 inch, R. H. M., 144 to pkg 
Pkg- 
SR00143 
Screw, 10-32 x 1 inch, R. H. M., 144 to pkg 
Pkg- 
SR00297 
Washer, screw size 10, 1 lb. pkg., 1,000 washers 
Pkg- 
SR00312 
Cord, no. 16, two-conductor, moisture resistant, asbestos 
packed 
ft. 
10 
SR00330 
Nut, 10 x 32, hex, 144 to pkg 
Pkg- 
SR00424 
Plug, male, two-prong, rubber covered 
ea. 
i 
*4 
SR00694 
Switch, 3 heat Arrow no. 9622 or Bryant no. 6269 
ea. 
i 
Uncommon Farts 
7R00602 
Cover, vitreous porcelain enamel 
ea. 
i 
4 
7R00604 
Jacket, outer, steel enameled 
ea. 
i 
4 
7R00606 
Boiler, cast iron 
ea. 
i 
7R00608 
Bottom, false 
ea. 
i 
7R00610 
Tray, instrument 
ea. 
i 
7R00612 
Tray, needle, brass 
ea. 
i 
7R00614 
Hook, tray 
ea. 
2 
*4 
7R00616 
Thermostat, positrol 
ea. 
1 
7R00618 
Leg, plastic 
ea. 
4 
4 
7R00620 
Element, heating, complete, assembly 
ea. 
1 
4 
7R00622 
Grill. For securing element 
ea. 
1 
4 
7R00624 
Spacer, iron 
ea. 
4 
7R00626 
Nut, bushing lock 
ea. 
1 
7R00628 
Bushing, porcelain 3/8 inch 
ea. 
1 
7R00630 
Wire, heater, asbestos covered. For internal wiring 
set 
1 
* To be requisitioned, when required, from the supply depot. 
No asterisk indicates that the item is not stocked as a Spare Part, but can be obtained by 
special requisition. 
15 APPENDIX III 
LIST OF ALL SERVICE PARTS 
American Sterilizer Co. 
Fig. 
No. 
Medical 
Dept. No. 
Nomenclature 
Unit 
Quan- 
tity 
• 
Common Parts 
SR00017 
Nut, 8 x 32, hex, 144 to pkg 
Pkg- 
SR00114 
Screw, 8-32 x 3/4 inch, R. H. M., 144 to pkg 
Pkg- 
SR00152 
Washer, lock, screw size 8, 1,000 to pkg 
Pkg- 
SR00312 
Cord, no. 16, two-conductor, moisture resistant, asbestos 
packed 
ft. 
10 
SR00424 
Plug, male, two-prong, rubber covered 
ea. 
1 
SR00629 
Screw, 1/4-20 x 1-inch, fill. H. M., 144 to pkg 
pkg- 
* 
SR00694 
Switch, 3 heat Arrow no. 9622 or Bryant no. 6269 
ea. 
1 
Uncommon Parts 
7R00202 
Jacket, outer, sheet metal, galvanized 
ea. 
1 
7R00204 
Cover, complete. Assembly 
ea. 
1 
7R00206 
Hinge, x 1% inch with 1/8-inch pin 
ea. 
2 
* 
7R00208 
Handle, bakelite 
ea. 
1 
7R00210 
Tray, instrument 
ea. 
1 
7R00212 
Tray, needle 
ea. 
1 
7R00214 
Nut, heater head 
ea. 
1 
7R00216 
Gasket, heater head 
ea. 
1 
7R00218 
Heater, type D, 1600 watt, 115 volt, chromalox, com- 
plete. Assembly 
ea. 
1 
* To be requisitioned, when required, from the supply depot. 
No asterisk indicates that the item is not stocked as a Spare Part, but can be obtained by 
special requisition. 
16 APPENDIX IV 
War Model 214C 
Pelton and Crane Co. 
Fig. 
No. 
Medical 
Dept. No. 
Nomenclature 
Unit 
Quan- 
tity 
Common Parts 
SR00040 
Screw, 6-32 x 1/4 inch, R. H. M., 144 to pkg 
Pkg- 
SR00140 
Screw, 10-32 x 1/4 inch, R. H. M., 144 to pkg 
Pkg- 
SR00265 
Screw, 8-32 x 5/8 inch, R. H. M., 144 to pkg 
Pkg- 
SR00312 
Cord, No. 16, two conductor, moisture resistant, asbestos 
packed 
ft. 
10 
SR00330 
Nut, 10-32, hex, 144 to pkg 
Pkg- 
SR00424 
Plug, male, two prong, rubber covered 
ea. 
i 
SR00479 
Screw, 1/4-20 x 3/8 inch, R. H. M., 144 to pkg 
pkg- 
SR00693 
Screw, 4-36 x 1/2 inch, R. H. M., 144 to pkg 
Pkg- 
SR00694 
Switch, 3 heat Arrow No. 9622 or Bryant No. 6269 
ea. 
i 
SR00695 
Screw, 12-24 x 3/8 inch, R. H. M., 144 to pkg 
Pkg- 
SR00881 
Wire, No. 14, copper, solid, asbestos insulated, white, 
moisture and heat resistant 
ft. 
4 
Uncommon Parts 
7R00002 
Rod, porcelain 
ea. 
1 
7R00004 
Trip, cut-off 
ea. 
1 
7R00006 
Coupling, adjustable. For trip 
ea. 
1 
7R00008 
Knob, plunger, low water cut-off 
ea. 
1 
7R00010 
Plunger, low water cut-off 
ea. 
1 
* 
7R00012 
Blade, contact, low water cut-off 
ea. 
2 
♦ 
7R00014 
Drum, contact, low water cut-off 
ea. 
1 
7R00016 
Block, contact, porcelain, low water cut-off 
ea. 
1 
7R00018 
Cover, enamel 
ea. 
1 
7R00020 
Jacket, outer, galvanized, H. D. iron 
ea. 
1 
7R00022 
Boiler, cast iron, enameled 
ea. 
1 
7R00024 
Hinge, cover 
ea. 
2 
7R00026 
Nut, bushing. For lever 
ea. 
1 
7R00028 
Handle, lever 
ea. 
1 
7R00030 
Lever, elbow cover lift 
ea. 
1 
7R00032 
Coupling, lever. For cover lift 
ea. 
1 
7R00034 
Leg, plastic , 
ea. 
4 
7R00036 
Elbow, cover lift 
ea. 
1 
7R00038 
Tray, instrument 
ea. 
1 
7R00040 
Tray, needle 
ea. 
1 
7R00042 
Hook, tray 
ea. 
2 
7R00044 
Bottom, false 
ea. 
1 
* 
7R00046 
Element, heating for model 214C complete assembly, two 
elements with insulating sheets and rivets 
ea. 
1 
7R00048 
Spring, rod, low water cut-off 
ea. 
I 
7R00050 
Wire, heater, asbestos covered. For internal wiring 
set 
1 
* To be requisitioned, when required, from the supply depot. 
No asterisk indicates that the item is not stocked as a Spare Part, but can be obtained by 
special requisition. 
17 APPENDIX V 
Pre-War Model 214C 
Pelton and Crane Co. 
Fig. 
No. 
Medical 
Dept. No. 
Nomenclature 
Unit 
Quarv 
tity 
Common Parts 
SR00003 
Screw, 8-32 x 1/2 inch, R. H. M., 144 to pkg 
pkg. 
SR00040 
Screw, 6-32 x 1/4 inch, R. H. M., 144 to pkg 
Pkg- 
SR00140 
Screw, 10-32 x 1/4 inch, R. H. M., 144 to pkg 
pkg- 
SR00265 
Screw, 8-32 x 5/8 inch, R. H. M., 144 to pkg 
pkg- 
SR00312 
Cord, No. 16, two-conductor, moisture resistant, asbestos 
packed 
ft. 
1 
SR00330 
Nut, 10 x 32, hex, 144 to pkg 
pkg- 
SR00424 
Plug, male, two-prong, rubber covered 
ea. 
1 
SR00479 
Screw, 1/4-20 x 3/8 inch, R. H. M., 144 to pkg 
Pkg- 
SR00593 
Setscrew, 8-32 x 1/4 inch, headless, cup pt., 100 to pkg .. 
pkg- 
SR00693 
Screw, 4~36 x 1/2 inch, R. H. M., 144 to pkg 
pkg- 
*5 
SR00694 
Switch, 3 heat Arrow No. 9622 or Brvant No. 6269 
ea. 
1 
SR00695 
Screw, 12-24 x 3/8 inch, R. H. M., 144 to pkg 
pkg- 
* 
SR00881 
Wire, No. 14, copper, solid, asbestos insulated, white, 
moisture and heat resistant 
ft. 
4 
Uncommon Parts 
5 
7R00002 
Rod, porcelain 
ea. 
1 
5 
7R00004 
Trip, cut-off 
ea. 
1 
7R00006 
Coupling, adjustable. For trip 
ea. 
1 
5 
7R00008 
Knob, plunger, low water cut-off 
ea. 
1 
5 
7R00010 
Plunger, low water cut-off 
ea. 
1 c 
*5 
7R00012 
Blade, contact, low water cut-off 
ea. 
2 
*5 
7R00014 
Drum, contact, low water cut-off 
ea. 
1 
5 
7R00016 
Block, contact, porcelain, low water cut-off 
ea. 
1 
7R00018 
Cover, enamel 
ea. 
1 
7R00020 
Jacket, outer, galvanized, H. D. iron 
ea. 
1 
7R00022 
Boiler, cast iron, enameled 
ea. 
1 
7R00024 
Hinge, cover 
ea. 
2 
7R00026 
Nut, bushing. For lever 
ea. 
1 
7R00028 
Handle, lever '. 
ea. 
1 
7R00030 
Lever, elbow cover lift 
ea. 
1 
7R00032 
Coupling, lever. For cover lift 
ea. 
1 
7R00034 
Leg, plastic 
ea. 
4 
7R00036 
Elbow, cover lift 
ea. 
1 
7R00038 
Tray, instrument 
ea. 
1 
7R00040 
Tray, needle 
ea. 
1 
7R00042 
Hook, tray 
ea. 
2 
7R00044 
Bottom, false 
ea. 
1 
*5 
7R00046 
Element, heating, for model 214C complete: Assembly, 
two elements with insulating sheets and rivets 
ea. 
1 
5 
7R00048 
Spring, rod, low water cut-off 
ea. 
1 
5 
7R00050 
Wire, heater, asbestos covered. For internal wiring 
set 
1 
5 
7R00052 
Knob, valve plug 
ea. 
1 
7R00054 
Plug, drain-off valve /. .. 
ea. 
1 
5 
7R00056 
Body, drain-off valve 
ea. 
1 
7R00038 
Washer, rubber. For drain-off plug 
ea. 
1 
7R00060 
Support, tray, right hand 
ea. 
1 
7R00062 
Support, tray, left hand 
ea. 
1 
7 R00064 
Cover, chrome finish 
ea. 
1 
7R00066 
Jacket, chrome finish 
ea. 
1 
* To be requisitioned, when required, from the supply depot. 
No asterisk indicates that the item is not stocked as a Spare Part, but can be obtained by 
special requisition. 
18 APPENDIX VI 
Model No. WPB-13 
Wilmot Casde Co. 
Fig. 
No. 
Medical 
Dept. No. 
Nomenclature 
Unit 
Quan- 
tity 
Common Parts 
SR00035 
Screw, 8-32 x 5/16 inch, R. H. M., 144 to pkg 
Pkg- 
SR00040 
Screw, 6-32 x 1/4 inch, R. H. M., 144 to pkg 
Pkg- 
SR00152 
pkg. 
SR00153 
Washer, lock, screw size 6, 1,000 to pkg 
Pkg- 
SR00185 
Nut, 8-32, hex, brass, 144 to pkg 
pkg- 
SR00304 
Washer, screw size 8, 1 lb. pkg., 1,300 washers 
Pkg- 
SR00312 
Cord, No. 16, two conductor, moisture resistant, asbestos 
packed 
ft. 
10 
SR00330 
Nut, 10-32, hex, 144 to pkg 
Pkg- 
SR00368 
Screw, 10-32 x 7/8 inch, R. H. M., brass, 144 to pkg 
Pkg- 
SR00396 
Nut, cap, 5/16 x 18, hex, 100 to pkg 
Pkg- 
SR00404 
Washer, screw size 5/16, 5 lb. pkg., 450 washers 
Pkg- 
SR00424 
Plug, male, two prong, rubber covered 
ea. 
1 
SR00611 
Screw, 6-32 x 3/8 inch, fill. H. M., 144 to pkg 
pkg- 
*6 
SR00694 
Switch, 3 heat Arrow No. 9622 or Bryant No. 6269 
ea. 
1 
SR00697 
Screw, 1/4-20 x 3/8, O. H. M., 144 to pkg 
Pkg- 
Uncommon Parts 
7R00402 
Handle, lever 
ea. 
1 
7R00404 
Lever, elbow cover lift 
ea. 
1 
7R00406 
Coupling, lever. For cover lift 
ea. 
1 
7R00408 
Cover, chrome, complete with hinges 
ea. 
1 
6 
7R00410 
Boiler, cast 
ea. 
1 
6 
7R00412 
ea. 
1 
7R00414 
Leg, plastic 
ea. 
4 
7R00416 
Bottom, false 
ea. 
1 
6 
7R00418 
Spacer, brass 
ea. 
4 
*6 
7R00420 
Thermostat 
ea. 
1 
6 
7R00422 
Brace, angle. For switch 
ea. 
1 
7R00424 
Tray, needle 
ea. 
1 
7R00426 
Tray, instrument 
ea. 
1 
7R00428 
Hook, tray 
ea. 
2 
6 
7R00430 
Element, heating for model WPB-13 complete. Assembly. 
ea. 
1 
6 
7R00432 
Grill. For securing elements 
ea. 
1 
* To be requisitioned, when required, from the supply depot. 
No asterisk indicates that the item is not stocked as a Spare Part, but can be obtained by 
special requisition. 
19 APPENDIX VII 
Model No. C-413 
Wilmot Castle Co. 
Fig. 
No. 
Medical 
Dept. No. 
Nomenclature 
Unit 
Quan- 
tity 
Common Parts 
SR00035 
Screw, 8-32 x 5/16 inch, R. H. M., brass, 144 to pkg 
Pkg- 
SR00040 
Screw, 6-32 x 1/4 inch, R. H. M., 144 to pkg 
Pkg- 
SR00152 
Washer, lock, screw size 8, 1,000 to pkg 
Pkg- 
SR00133 
Washer, lock, screw size 6, 1,000 to pkg 
Pkg- 
SR00185 
Nut, 8 x 32, hex, brass, 144 to pkg 
Pkg- 
SR00304 
Washer, screw size 8, 1 lb. pkg., 1,300 washers 
Pkg- 
SR00312 
Cord, No. 16, two conductor, moisture resistant, asbestos 
packed 
ft. 
10 
SR00330 
Nut, 10 x 32, hex, 144 to pkg 
Pkg- 
SR00368 
Screw, 10-32 x 7/8 inch, R. H. M. brass, 144 to pkg 
Pkg- 
SR00396 
Nut, cap, 5/16 x 18, hex, 100 to pkg 
Pkg- 
SR00404 
Washer, screw size 5/16, 5 lb. pkg., 450 washers 
Pkg- 
SR00424 
Plug, male, two prong, rubber covered 
ea. 
1 
SR00611 
Screw, 6-32 x 3/8 inch, fill. H. M., 144 to pkg 
Pkg- 
SR00697 
Screw, 1/4-20 x 3/8 inch, O. H. M., 144 to pkg 
Pkg- 
Uncommon Parts 
7R00402 
Handle lever 
ea. 
1 
7R00404 
Lever, elbow cover lift 
ea. 
1 
7R00406 
Coupling, lever. For cover lift 
ea. 
1 
7R00408 
Cover, chrome, complete with hinges 
ea. 
1 
7R00410 
Boiler, cast 
ea. 
1 
7R00412 
Jacket 
ea. 
1 
7R00414 
Leg, plastic 
ea. 
4 
7R00416 
Bottom, false 
ea. 
1 
7R00418 
Spacer, brass 
ea. 
4 
* 
7R00420 
Thermostat 
ea. 
1 
7R00424 
Tray, needle 
ea. 
1 
7R00426 
Tray, instrument 
ea. 
1 
7R00428 
Hook, tray 
ea. 
2 
7R00432 
Grill. For securing element 
ea. 
1 
7R00434 
Plug, drain-off valve 
ea. 
1 
7R00436 
Knob, valve plug 
ea. 
1 
7R00438 
Body, drain-off valve 
ea. 
1 
7R00440 
Lift, tray, complete. Assembly 
ea. 
1 
7R00442 
Cut-out, low water, complete. Assembly 
ea. 
1 
♦ 
7R00444 
Element, heating for model C-413 complete. Assembly 
with 2 blades mounted on pressure plate 
ea. 
1 
* To be requisitioned, when required, from the supply depot. 
No asterisk indicates that the item is not stocked as a Spare Part, but can be obtained by 
special requisition. 
20 
* U. S. GOVERNMENT PRINTING OFFICE: 628023-TM 1061